PERRIS AUTO SPEEDWAY
2014 FIGURE-8 RULES

COMPETING MODELS
This is an OPEN CLASS, any car or truck can compete. No convertibles (unless covered by a wing).

GENERAL CAR AND BODY REQUIREMENTS
1. Bodies must have doors, roof and quarter panels
2. No weight limit.

DETAILED CAR BODY REQUIREMENTS
1. Windshield and Windows: 1) There is to be no glass on the race car. 2) Full steel wire
mesh minimum 1/2-inch to 1-inch square metal in place of windshield is required. No
string nets.
2. Fenders optional.
3. Identification and Marking: Numbers must be on both sides of the car and on the roof.
4. Window Net: 1) Mandatory left side door window screen/net required. Net must be a rib type, made from minimum 3/4 inch wide, maximum one (1) inch wide nylon material.
Window net lower mount must be a solid steel rod (1/2 inch diameter recommended) on
the bottom with rod mounts welded to roll cage. Window net upper mount must be solid
steel (recommended one (1) inch wide by 3/16 inch flat steel rod or 1/2 inch diameter
rod) with mounts welded to roll cage. The window net, when mounted in the closed
position, must fit tight and secured with a lever-type quick release latch at top acceptable
to track officials.


PERSONAL SAFETY EQUIPMENT AND ROLL BARS
1. General Safety: 1) It is the responsibility of the driver, not Perris Auto Speedway , its
officers, or its agents to ensure his/her safety devices and systems are correctly
installed, maintained, and properly used at all times.
2. Protective Clothing: A clean full-length fire suit and safety gloves recommended. At a minimum, Long Sleeves, Long Pants. leather gloves and leather boots must be worn at all time. Racing shoes or leather shoes required.
3. Fire Control: Every car must be equipped with one fully charged fire extinguisher having at least a 10B:C rating. The fire extinguisher must be accessible to driver with quick release mount.
4. Helmets: Head and Neck Restraint Devices recommended. Snell approved helmet mandatory, SA2000 or newer, with face shield required. No Motocross Helmets.
Driver must rely on his own judgment in the selection of any helmet and apparel for durability and safety.
5. Seat Belts: Five-point, quick release restraint system with no less than 3-inches wide
recommended. Center crotch belt must be a minimum of 2 inches wide. Belts must be recertified or replaced every 3 years. Both ends must be fastened to roll bar cage with 3/8" grade 5 or better bolts. 4) Belts must be mounted per manufacturer's specifications. At a minimum, a lap and shoulder seat belt is required. No fiberglass, plastic or homemade seats allowed.
6. Roll Bars: A full roll cage is recommended. Steel plate of 1/4 inch must be on drivers door. All cage roll bar material must be a minimum of .090 wall steel 1-3/4 inch tubing. No galvanized pipe. Maximum tubing diameter 2-inch. No threaded pipe fittings allowed. All roll bar structure exposed to the driver must be padded with approved padding. The two uprights in the left side door must be padded.

DISCLAIMER
The rules and/or regulations set forth herein are designed for the orderly conduct of racing events and to establish minimum acceptable requirements for such events. The rules shall govern all entrants. NO EXPRESS OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM PUBLICATION OF OR COMPLIANCE WITH THESE RULES AND/OR REGULATIONS. They are intended as a guide for the conduct of the sport and are in no way a guarantee against injury or death to a participant, spectator or official.
The race director shall be empowered to permit deviations from any of the specifications, herein, or impose any further restriction, that in his opinion do not alter the minimum acceptable requirements. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM SUCH ALTERATION OF SPECIFICATIONS. Any interpretation or deviations of these rules is left to the discretion of the officials. Their discretion is final. If you have any questions please call the office at (951) 940-0134.

PURSE:

1. $500 2. $300 3. $200